weBoost Drive Reach 470154 spec sheet (PDF)
weBoost Drive Reach 470154 installation guide (PDF)
Poynting 
Poynting 
Poynting 
Top Signal EDGE panel antenna TS260820 spec sheet (PDF)
Wilson 
Wilson low-profile antenna 314401 spec sheet (PDF)
What’s my actual cell signal strength?
On Sale!
Free shipping on orders over $200!
The Drive Reach Class A & Class C 2-in-1 system uses weBoost’s most powerful mobile booster with upgraded antennas to provide better cell signal in your RV, motorhome, fifth wheel, or trailer. Stay connected longer with the strongest cell signal and experience fewer dropped calls, undelivered texts, and missed email messages. Keep your data moving faster in areas with weak cell service, obstructions, and long distances from cell phone towers.
The low-profile Poynting PUCK-1 outside donor antenna receives signal from cell towers and sends it to the Drive Reach booster to be amplified. It has 6.6′ (2 m) of thin coax cable that you’ll bring inside your motorhome through an available opening or a specially-drilled small entry point.
The PUCK-1 has 6 mounting options, including a 3M® adhesive pad, making it ideal for RVs without ladders and Class A motor coaches that have low-clearance concerns. (Click here to download the Poynting PUCK-1 PDF user guide with installation instructions.)
Surface mount with 3M® adhesive pad
Magnet mount
Spigot mount with 30 mm or 70 mm spigot
Pipe mount horizontal or vertical (zip tie or hose clamp required)
Wall mount (additional screws required)
Panel mount (longer M4 bolts may be required)
The Top Signal EDGE inside broadcast antenna sends signal from Drive Reach booster to cell phones, cellular hotspots, modems, and routers. It comes with 10′ (3 m) of flexible 195 coax cable.
The EDGE has 4 mounting options, allowing you to place it where you need signal most. It also stands upright on flat surfaces, so you can leave it unmounted move it where you need signal most. The back of the panel includes a channel for the pigtail cable so it will mount flush against walls and ceilings.
Freestanding stands upright on any flat surface
Wall mount with included bracket & mounting hardware
Ceiling mount with included mounting post & nylon nut
Adhesive mount with Command™ Strips or similar products (purchased separately)
Command™ brand is a trademark of 3M.
You can install the RV weBoost Drive Reach Class A & Class C 2-in-1 system yourself, or you can have it installed by an RV dealer or service center.
For instructions and tips on setting up this system in your RV, motorhome, or trailer, download the PDF installation guide.
This system has an optional 12V DC hardwire power supply with an inline 3-amp fuse. The hardwire kit connects directly to your vehicle’s DC power system, freeing up a 12V power socket and allowing for a less-cluttered installation. A hardwire power supply typically requires professional installation.
To get the DC hardwire power supply, use the dropdown option at the top of this page before clicking Add to Cart.
The Wilson 950079 DC hardwire power supply for the weBoost Drive Reach.
The weBoost app measures signal performance, pinpoints the nearest cell tower, and shows your cell signal strength before and after installation. It includes step-by-step setup instructions and how-to videos for weBoost products.
This is a complete kit, with everything you need to start getting the best signal in your motorhome or motor coach:
weBoost Drive Reach cell signal amplifier w/heat sink 460054
Mounting bracket for Drive Reach booster 990054
Wilson AC/DC wall outlet power supply 850041
Wilson 12V DC vehicle power supply 850029
Top Signal EDGE indoor panel antenna TS260820 w/connector & mounting hardware
10′ 195 coax w/N-male & SMA-male connectors TS333010
Poynting PUCK-1 antenna w/2 m RTK031 coax cable & SMA-male connector A-PUCK-0001-V1-01
M4 screws (×4)
Magnetic base plate
3M® foam adhesive pad
70 mm spigot
30 mm spigot
Spigot nut
Pole/wall bracket
Poynting PUCK-1 user guide
Wilson mag-mount “shark fin” antenna w/12.5′ LMR100 coax cable 311216
13⁄8″ (35 mm) steel disk adhesive antenna mount (for aluminum-body trucks)
Wilson low-profile inside antenna w/10′ LMR100 coax cable 314401
Hook-and-loop strip and alcohol prep pad (to mount the inside antenna)
weBoost Drive Reach installation guide
RV weBoost Drive Reach Class A & Class C installation guide TS023029
Optional add-onUsing Wilson Electronics’s patented technology, the weBoost Drive Reach receives the outside cell signal, amplifies it, and rebroadcasts it to a desktop-sized area. This allows you to stay connected in areas where cell service is poor, while you’re underway or parked.
The weBoost Drive Reach RV system works with all major wireless carriers, including Verizon, AT&T, T-Mobile, DISH Wireless, UScellular, GCI Alaska, and most others.
It operates on common cellular frequencies.
For information on federal rules governing the use of consumer cell signal boosters, please see our FCC notice page.
Warning This product can expose you to chemicals, including nickel, which is known to the State of California to cause cancer, and Bisphenol A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
.
Product Specifications
Warranty Information
For warranty information on this product, please see our weBoost warranty information page.
Questions & Answers
