Wilson 801280 AG Pro 75 Kit - Cell Phone Booster System

Product Description This dual-band 75dB (800/1900) system uses Wilson's largest dual-band building amplifier, Wilson 801280 AG Pro 75. The complete system has been designed to broadcast an improved cell signal into multiple rooms in homes and buildings. Broadcast distance will vary depending upon outside cell signal strength and carrier frequency. Interior and exterior antennas should be separated a minimum 50+ feet to avoid oscillation between antennas. This system requires installation. Add 2nd Antenna: This system is available with 1 or 2 interior antennas. If "Add 2nd Antenna" is selected an additional interior coax, interior antenna, 2-way splitter, and jumper are added. Even though the broadcast radius of each antenna is smaller on a 2-antenna system. The two antennas give your cellular repeater system more coverage area. Sometimes 2-antenna systems make it easier to cover odd-shaped buildings. View All AG Pro Systems	Sample 1 antenna installation
Kit Components (single antenna) Wilson 801280 AG Pro 75 Amplifier Choice of interior antenna (dome or panel) Choice of exterior antenna (Omni or directional) Choice of coax length to outside antenna Choice of coax length to interior antenna Universal J-Pipe Antenna Mount Lightning Surge Protector Components added (2nd antenna option) Additional Interior Coax Cable Additional Interior Antenna 2-Way Splitter 2' Jumper	Wilson 801280 AG Pro Kit Components (single antenna)
Installation Outside antenna needs to be mounted on the roof of your building. Outside antennas are designed to be mounted on a pole (max 2" diameter) using U-bolts. Coax needs to be run from the outside antenna to the amplifier. The amplifier can easily be mounted on a wall in an equipment, utility, or storage room. The inside antenna needs to be mounted on a ceiling (dome) or wall (panel). Coax needs to be run from the inside antenna to the amplifier. Standard wall plug power is required near the amplifier. Antennas do not require power.	Sample 1 antenna installation
Coverage Area Inside coverage distance varies depending upon outside signal strength, carrier frequency (800 or 1900Mhz) and interior obstacles. The Wilson 801280 AG Pro has been designed to provide approximately 500 to 1,000 sf of coverage in low signal areas (1 bar outside) and up to 10,000 sf in strong signal areas (4-5 bars outside). Note: These calculations are for 1900Mhz. 800MHz will provide more coverage. The addition of a 2nd antenna will increase your coverage area. Please consult with Powerful Signal to determine expected coverage area for your situation.	Sample 2 antenna installation
Antenna Separation Exterior and interior antennas need to have the proper separation. This is usually about 60+ feet depending upon several variables. Obstacles (metal, concrete, etc.) between antennas Difference in height between antennas. Vertical separation is very effective. Contact Powerful Signal for more information regarding antenna separation. We will help you design your system properly.

Wilson 801280 AG Pro 75 Amplifier The new Wilson 801280 AG Pro has the ability to manually adjust each frequency, 800Mhz and 1900Mhz with a separate control knob. This easy-to-use adjustment method makes system setup and operation easy and simple to understand. This amplifier runs at 70dB Gain Typical and 75dB Gain maximum. Indicator lights on the amplifier are used to help adjust the amplifier during setup. Red lights indicate error conditions, which means the amplifier gain (broadcast power) needs to be turned down. Green lights indicate the amplifier is operating without any errors. Wilson SMART technology turns the amplifier off if any error conditions are detected.	Side View	Top View
Exterior Antennas A choice of two different exterior antennas are offered. 5dB gain Omni fiberglass 9dB gain directional The omni antenna collects signal from 360 degrees, all directions. This antenna is generally recommended, and it works well in most situations. The directional must be pointed in the direction of the cell tower(s). This antenna works best when there is a good line-of-site to the cell tower or the terrain is mainly flat or low rolling hills. Not recommended in low spots or dense forested areas. Both antennas work with 800/1900MHz carriers. Mounting hardware is included and installation is required. A J-Pipe Universal Antenna Mount is included with the system. This mount allows the exterior antenna to be mounted on either a wall or the roof.	Omni-Directional Antenna	Directional Antenna J-Pipe Universal Antenna Mount
Interior Antennas A choice of two different interior antennas is also offered: Omni-directional ceiling mount dome Directional wall mount panel The dome is recommended in most situations when an attic or dropped ceiling is available. A panel is recommended in homes with vaulted ceilings and situations where antennas cannot be mounted on the ceiling.	Dome Antenna	Panel Antenna
Coax This system provides two lengths of 400 low loss coax. One length is used from the amplifier to the interior antenna. The other length is used from the amplifier to the exterior antenna. Select lengths that best fit your installation environment. Remember: each foot of coax is signal loss, so don't just get the longest length. Figure what you need and select the length that best fits. Note: *Never* coil excess coax. It will cause problems.
Lightning Surge Protector A lightning sure protector is provided with this kit to help protect your amplifier and components from damage. The surge protector is attached between the exterior antenna and the coax cable going to the amplifier. The surge protector has the ability to be grounded.